@Zaemo wrote:
Sparkfun XBee Explorer Regulated WRL-11373.
The old version is in the Fritzing library. The long side pins have relocated inward on the current version. When I asked about it on their forum they said it was “in the library.” Didn’t seem to be a bother to them.
I have made three headers that I drag onto the board and align by sight and I can drag the old version over the top to check the overall footprint, then I drag it back out of the way.
Thank You!
Posts: 2
Participants: 2
@hassanbasri99 wrote:
Hello!
I am new to this forum, I have recently started using Fritzing 0.8.7b but I’m unable to find the library for a barcode scanner (NTEUMM) for a smart lock project that I’m currently working on, If you guys can help me find the any libraries relating to the barcode scanner that’ll be great.
Posts: 2
Participants: 2
@marktroll wrote:
I’m new to fritzing and play a bit around… Now I need help…
I search for the part file of a 3.5mm jack. This Model:
Regards
Posts: 1
Participants: 1
@zoompankaj wrote:
Hi, just now installed the windows version code of Fritzing and tried to install it. Its is not beginning installation and no error is also reported. I had made the payment through PayPal after which i received the link and even downloaded it twice but of no help. I am trying it on a HP PC with Windows 10 License copy so no case of piracy also. Please help.
Thanks in advance
Pankaj
Posts: 2
Participants: 1
@volker1078 wrote:
Hi there,
I am looking for the following component for my project:
https://www.reichelt.de/printtrafo-2-va-2x-6-v-2x-166-ma-rm-20-mm-ei-30-15-5-206-p27333.html?r= 1
has someone already created such a component for the PCB view or can do it for me?
Greetings Volker
Posts: 1
Participants: 1
@boylesg wrote:
Does anyone have these parts that they can email me?
gregplants@bigpond.com
Posts: 2
Participants: 2
@Ivo_Limpens wrote:
For (the schematics of) an assignment, I am looking for something that could function as a 10V (100mA) power supply? But so far, I haven’t been able to find a part for it. I like using the breadboard to schematics capabilities of fritzing, but without the parts I need for this one, I will end up having to use some other software.
Below is the example image provided to us in the assignment.
On a side note: Not sure what I am going to use for Vout yet.
Posts: 3
Participants: 2
@volker1078 wrote:
Hi there,
I am looking for the OPA454 operational amplifier for my circuit. Unfortunately, I do not find any pin compatible with the OP. Has anyone created one or is there at least one that is so similar?
Here is the data sheet of the OP:
http://www.ti.com/lit/ds/symlink/opa454.pdf
Greetings Volker
Posts: 1
Participants: 1
@JonMiles wrote:
I am trying to make my first PCB to be sent off for manufacturing, one of the “suggestions” i keep hearing is to avoid 90° corners in the copper.
is there a way to set this as an option in autorouting?
as you can see i have a number of 90° corners.
Many thanks in advance
Posts: 2
Participants: 2
@bigc7 wrote:
Does anyone happen to have the ESP32-CAM part handy? I’ve looked for it but can’t seem to track it down.
Posts: 2
Participants: 2
@AndyPF wrote:
Is it any way to change the colors of the tracks in PCB view? For example in order to use red for top copper and green for bottom copper?
I can’t find any setting for that, maybe I’m wrong…
Posts: 1
Participants: 1
@simionovdaniel10 wrote:
Hello,
I recently bought the latest version of fritzing and I found out that the search button doesn’t appear in the parts section. I also tried to search the button in the folder and no results were found. Please, I need some help because it is difficult to find a part in so many libraries. I also have a problem with adding a new components to the parts section so I really need a solution for this problem too!
Posts: 2
Participants: 2
@Time_Wolf wrote:
OSX = 10.14.2
Fritzing 0.94Why to I keep finding I have to wait 60 seconds between function calls?
File open is the worst culprit in that it takes over 60 seconds to open the dialog and then another 60 to click on the search and then another 60 to start typing!
Posts: 1
Participants: 1
@donate wrote:
I need the component file (. Fzb file) of photosensitive sensor and DS1302 and infrared remote controller. I hope someone can give me.Thanks!
Posts: 2
Participants: 2
@danihibari wrote:
Good morning everyone. I wanted to ask if someone has created HORIZONAL momentary buttons of various sizes. I can’t find them in the parts. Possible?
Thanks in advance.
Posts: 2
Participants: 2
@Cecile wrote:
Hi,
I am looking for the part DFR0165 (Gravity: IO Sensor Shield For Arduino Mega Due) in fritzing but it does not exist in fritzing. Could someone help me please ?
Thanks !
Cécile
Posts: 7
Participants: 3
@Maver wrote:
Hello, I’m a newbie. Can anyone help me with Keyes L298 in fritzing?
Posts: 2
Participants: 2
@jhershey69 wrote:
New here and any help appreciated.
Looking for this part https://github.com/Xinyuan-LilyGO/TTGO-T-Display
I wish I could find a drawing but, no. I can design the circuit without it on a breadboard, it’s 24 pins standard spaced I guess. Will this software allow any old part on the breadboard that has the same pin configuration?
Posts: 2
Participants: 2
@DingDong wrote:
Hi
I’m new to using Arduino my Arduino is an Arduino R3 I want to wire a push Button or a spring loaded center off toggle switch to a breadboard kit i had purchase i want to move a servo horn from position A to position B and back to position A when the button or toggle switch is activated looking for some help with this thanks in advance.
Posts: 4
Participants: 2
