@Old_Grey wrote:
I don’t know if anyone would want this because they seam to be non existent these days.
Small Transformer - 14mm sq core - 19mm wide - 15mm high - 2 Primary pins - 3 Secondary pins
v1 - Transformer.fzpz (8.8 KB)
Posts: 1
Participants: 1
@Old_Grey wrote:
This one needs fixing to make it good, but it works.
Don’t know how to draw a glass wheat bulb in BB view.
For some reason the outline is grey in PCB view.Neon Lamp 6mm x 16mm to tip
v1 - Neon Lamp.fzpz (6.9 KB)
Posts: 1
Participants: 1
@Old_Grey wrote:
This triggers Xenon Flash tubes
Trigger Coil Transformer
v1 - Trigger Coil Transformer.fzpz (7.7 KB)
Posts: 1
Participants: 1
@amanda121287 wrote:
Steps I took that resulted in the problem:
Extended stripboard beyond the default value. The extended area is created as all tracks connected matrix, not strips.What I expected should have happened instead:
Stripboard with strips appearing to extended areaMy version of Fritzing and my operating system:
Win 10 64 bit, 0.9.3bPlease also attach any files that help explaining this problem
Posts: 2
Participants: 2
@phischmi wrote:
Hi all,
for my actual project i’m using a Recom R-78E5.0-0.5 SIP3 switching voltage regulator.
Sadly i couldn’t find that part in fritzing
Is there anything similar i can use for creating a pcb with this part or have i just missed it?Thank you very much!
Philipp
Posts: 3
Participants: 3
@MadHatter wrote:
I am looking for this part if anyone has it or wants to make it for me let me know thanks
https://www.digikey.com/product-detail/en/linx-technologies-inc/HUM-900-PRC/HUM-900-PRC-ND/7691362
Posts: 2
Participants: 2
@amowry wrote:
Fritzing doesn’t seem to be using a consistent keepout distance around my SMD pads. In the attached image, you can see that some pads have no keepout, some have a small keepout of around 2 mils, and some have the “normal” keepout of 6 mils. Even within identical pads on the QFN part, some pads have no keepout and some have alarge keepout that bleeds together. Any ideas what is causing this? Does inconsistency in SVGs for parts influence this somehow (maybe strike width??)
Thanks!
What I expected should have happened instead:
Consistent mask keepout around pads
My version of Fritzing and my operating system:
Windows 10, Fritzing 0.9.3
Please also attach any files that help explaining this problem
Posts: 2
Participants: 2
@Old_Grey wrote:
I don’t know how to draw glass for BB view
Xenon Flash Tube U
v1 - Xenon Tube U.fzpz (7.5 KB)
Posts: 1
Participants: 1
@gemini07 wrote:
Hello everyone,
I am French and I am a beginner on Fritzing as well as on this forum.
I wish I could create a stripboard like the one visible in this photo :
![]()
(I have many breadboards like this one)
I have watched this video several times, but I do not understand how the guy came to create this streapboard on Fritzing :
Is it possible ? If yes, how ?
Thank you for your help
Posts: 1
Participants: 1
@Eddiie wrote:
Hi,
Very new to Fritzing, it is awesome! Thank you.
I have a test shield for the Uno that has a built-in SD card. My project has exceeded the capacity of an Uno and was looking to use a Mega 2560. Plugged in my card only to find the SPI pins on the mega have moved to the ICSP header. Most of my shields use the SPI pins on the Uno, 11, 12, 13 I believe they are…
It seems one can make an adapter shield with jumpers of some sort that can ‘map’ the functionality of the SPI pins between 11, 12, 13 to the ICSP header, maybe another setting to make the pins pass-thru to other shield, etc.
Before going down this path, surely someone has done this already or there is some obvious problem that I am missing.
Let’s say I have to make one or decide to make one of my own for whatever reason… The ICSP header I would want to use would be a long pinned female type connector pass-thru hole … ? I did not find this part in the large list of parts. Am I missing it?
Lastly, if I add my own SD card, is there a chip of some sort needed? Or do the pins go directly to the ICSP pins? My existing shield looks like it has a real small ship with no markings that I can see.
Thank you!
Posts: 5
Participants: 3
@Old_Grey wrote:
Steps I took that resulted in the problem:
It’s probably not worth reporting, but if you complete the SCH with it’s connections and go back to BB view and bend a leg, that parts becomes disconnected.
In fact if you do SCH view first and try to do BB after you can’t grab legs on small pin parts to bend them because the mouse click always grabs the ratsnest first.
…What I expected should have happened instead:
Part stay connected in the circuit
…My version of Fritzing and my operating system:
v9.3 Win7 64
…Please also attach any files that help explaining this problem
Posts: 1
Participants: 1
@Eddiie wrote:
I am making an Arduino shield of sorts. It is almost ready but I need a couple parts to finish it off.
Is there parts out there for the Arduino headers with the long pins and female headers? Same for the ICSP pins?
If not, I’d like to just leave the usual solder holes and I’ll source the parts myself. I cannot seem to find a simple hole for soldering pins on a through-hole component. I find the mounting hole object.
Thanks!
Posts: 1
Participants: 1
@Old_Grey wrote:
Sorry, back again
I made this circuit based on a vid from The Signal Path because it’s simple. The circuit has to be simple, cheap, with easy to find parts.
When I apply 5V - voltage doesn’t makes much difference - it only puts out 55V across C1, when I need 300V.
The only transformers I could find were in old transistor radios, so is the transformer wrong?
I did some Googling and it said the only way to work out unknown transformers is test and measure.Just the power side so far.
Original
![]()
Posts: 9
Participants: 3
@opera_night wrote:
In another link, I posted info on the sdCard Adapter I use (senmod sdhc adapter). I’ve used them enough now that I decided to make a ‘Part’ for it.
Info:
• I like big pads so, the pads are for my preference and my cause you DRC errors (depending upon your DRC settings). My DRC settings are for 0.010 inch Keepout to avoid error. (FYI - you can ignore these errors and export the gerbers).• I prefer to lay the adapter parallel with the PCB using a 90º Pin Header. Therefore, in the PCB layout, the Pin’s are reversed and enclosed in a dashed box. The Breadboard and Schematic views are as normal. As there are no internal connections, you can ignore pin labels and hook-up as you prefer. Of course, you don’t need to lay it parallel to PCB - your preference…
• I also prefer larger text so the pin#'s are readable.
my_sdCard.fzpz (10.5 KB)
Posts: 4
Participants: 2
@somsak wrote:
My pcb is 20x22mm. The quote price from manufacture is the same upto 50x50mm. I am finding the way to make multiple pcbs on one gerber file. This case can have 4 pcs on 50x50 order and when it arrives I will cut it by myself to four pieces.
The problem is how can I generate 4 PCBs in one Gerber file.
Somsak
Posts: 5
Participants: 3
@thomasniederberger wrote:
GPD2846A - TF Card MP3 Decoder Board Module
GPD2846A.fzpz (17.8 KB)
Posts: 1
Participants: 1
@gemini07 wrote:
Hello friends,
would there be someone nice here, to make me a simple electric wire?
I did not find that kind of thing to download.
I wish I could change its length, color and thickness (fine wire) .
Many tank’s
Posts: 1
Participants: 1
@gemini07 wrote:
Ability to use components allocated in the schematic view for the breadboard or streapboard ,
if it’s possible .
Posts: 1
Participants: 1
@dhlii wrote:
When a connection is marked as a groundfill seed, and there are no wires connected to it, that connection is represented as unconnected.
Posts: 2
Participants: 2
@dhlii wrote:
Groundfilling is very useful.
But it should be possible to VCC fill the opposite layer of the board, and it should be possible to mark a pin as VCC Seeded.
Posts: 2
Participants: 2
