Fritzing file ruined
@StaffanEk wrote: Steps I took that resulted in the problem: I worked and saved occasionally. All of a sudden I get warning messages when I save. I cannot tell what I exactly did but I edited some of...
View ArticleFritzing Installation Problem on Linux
@Sydcee wrote: I removed Windows & changed my Computer to run on the Linux operating system. I have not been able to re-install Fritzing on the Linux Operating System. Can someone please assist...
View ArticleMake Parts And Place them in Fritzing
@garywatson wrote: I would like to say It is very flustering to try to make a PCB , And you find that the simplest and most used parts or not in Fritzing , Here are a few I could use a 18650 battery...
View ArticleIs Fritzing dead? No updates since June 2016
@Hex wrote: Is Fritzing dead? No updates since June 2016. Today it is the 16th of October 2018. But it is free, so I can’t ask for my money back… Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
4 Way Traffic light Circuit
@garywatson wrote: I have Assembled this circuit several time on a Breadboard and I can Not get it to work Correctly , If I am understanding the schematic Correctly this is how it is Supposed to be...
View ArticleClik here to view.
GY273 QMC5883L Triple Axis Magnetometer Breakout
@Niccolo wrote: This is a small breakout, which is different from another already shared here. It has the the same chip, but different footprint and pinout. The silkscreen has the writing HMC5883L,...
View ArticleClik here to view.
U-blox NEO-6M GPS Breakout
@Niccolo wrote: This is a small breakout holding the u-blox NEO-6M GPS module. Serial interface plus a Pulse Per Second pin. u-blox-neo-6m-gps.jpg1200x1600 294 KB u-blox-NEO-6M-GPS_Breakout.fzpz (5.6...
View Article4017IC Traces on bottom not working
@garywatson wrote: I Seem to have a problem in Fritzing with My 4017 IC When I place the 4017 Ic On the Design And run traces to the IC . The program will not allow me to Place the trace on the bottom...
View ArticleClik here to view.
Special TYPE of SPST (part)
@Drakkheen wrote: Hi im looking for a specific type of SPST to draw circuits for my pupils. We are using ONLY that type of switch and for SOME of them its too difficult to build from sketches with...
View ArticleGeneric ICs with oblong/rectangular pads?
@noiasca wrote: is there an easy way to get a (generic) IC with “oblong” / rectangular - non round - through the hole pads to enable routing of small wires between the pads? Currently I need ICs...
View ArticleBME / BMP 280 sensor
@mtd wrote: Hi, I’ve created a new Fritzing part - BME/BMP280 - temperature, humidity, barometric sensor with I2C protocol. Download here: ajcreatif.com/BME280.fzpz Thanks for using. Regards, mtd...
View ArticleInvisible text in my part
@dvarrel wrote: hello, none of the text with OCRA font is visible on my breadboard part. if i convert it into path it’s ok what’s the reason ? here’s the inkscape svg...
View ArticleThe Pressure Stat in Washing Machine
@ercngl wrote: Dear All, I am working on a project which checks the pressure sensor in washing machine that is ok or nok. First of all, let me explain how a pressure sensor works. It is a circuit...
View ArticleDoit esp32 devkit v1
@noiasca wrote: I want to share a part: It is a DOIT ESP32 DEVKIT V1 with 30 pins. The pins are (obvious) in two rows and the distance between the two rows is 1100 mil. The pads are oblong/rectangular...
View ArticleUpgrade of Library
@KeithSloan wrote: Had not run Fritzing for quite some while. It offered to upgrade my library, which I let it do. I now get the following errors on startup Unable to find the following 2 parts:...
View ArticleConnecteur JST-XH 2.54mm
@MOMO17700 wrote: Hello everyone! Before going further, is there a forum page in French? If so can you please give me the link? Thanks in advance. So I am looking for a library for Connectors JST-XH...
View ArticleStrain Gauge Module BF350-3AA
@TH3xTr3MiST wrote: can someone help me create this part for fritzing i want to complete my final year project schematics thanksthis Posts: 3 Participants: 2 Read full topic
View ArticleDownloaded a part I need that has errors that I want to try to fix
@Lineaxe wrote: When I connect the Vcc it shows it as ground in the schematic view… Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Update window to high
@Hoffmann wrote: Open “Search for updates” in the “Help” menu. Window with update information is neither resizeable nor fully viewable due to window height. … Have an information window about a...
View ArticleExporting circuit with HC-05 as SVG, module not found
@cyberpulsar wrote: Steps I took that resulted in the problem: Export a circuit with the HC-05 module as SVG I’ve also tried downloading...
View Article