Unwanted Scrolling
Steps I took that resulted in the problem: Working on smaller screens, on the notebook for example, leads to a smaller Inspektor-window. When I scroll the Inspektor-window down to get to the dropdown...
View ArticleDisplay of percentage of Resistors etc
An Option to lock all parts in a schematic frame would be nice. I didn’t found the option to display the percentage of the Resistors in the schematic, just like the resistance is displayed. Is there...
View ArticleClik here to view.
Help with schematic mode
I’m supposed to convert this image ( image1024×894 216 KB ) into schematic mode, I’ve gotten all the components into fritzing but I have no idea how to connect the cables. Please help 1 post - 1...
View ArticleGeneric part options disabled
Hi, i am starting with Fritzing and I was trying to modify default options for some generic parts but all combo boxes are greyed out and when hovering over the parts icons the mouse cursor displays a...
View ArticleClik here to view.
Looking for a 8-pin PCIe Connector
Something like this: modDIY.com 8 Pin Graphics Card PCIe Male Header Connector 90 Degree Angled Black Buy 8 Pin Graphics Card PCIe Male Header Connector 90 Degree Angled Black for $1.99 with Free...
View ArticleRS PRO, x Way PCB Terminal Block
Hello, Currently I’m using something quite similar to this (Camdenboxx_CTB0158-8), but the PCB footprint isn’t the same (the CB part has a 90degree input for the wire, whereas the RS part is a push in...
View ArticleBreadboard Full+ Half Power Rails
hello all, I’m currently using the ‘full’ varient of the breadboard on the parts library, but I keep getting lost as to which is the positive and negative/gnd rails. I found that the ‘full +’ board...
View ArticleClik here to view.
Parts couldn't be shown after installing on UBUNTU
I have installed Fritzing on Ubuntu, it could run, but the parts was empty. When I double-click Fritzing snd open it, 3 prompts windows came continuously after each “OK” Screenshot from 2020-05-15...
View ArticleClik here to view.
Parts are displayed out of place in the schematic view
I want to create a PCB-LQFP64 part, but when I place the part, the pins in the schematic view are displayed out of alignment. What can I do to fix this? The original SVG file created by Inkscape and...
View ArticleCreate custom part based on generic one
Hi all, I am trying to create a custom part (stripboard PCB) based on the generic one. The difference with the generic PCB is that the one I got (50 units) have a strip pattern linking 3 consecutive...
View ArticleClik here to view.
Add wire in Perf Board
Hi, I firstly used a perf board in breadboard view to build a little prototype. But I cannot connect solder points from a point which are still connected. In some discussion here there was a tipp to...
View ArticleClik here to view.
(beginner) help with nodeMCU / ESPHome multisensor
Hi everybody, I am currently trying to create a multi sensor on a nodeMCU (HW-625) running ESPHome. I had attempted this before, but eventually decided I’d start from scratch. The device is currently...
View ArticlePart connector name rules
What are the real rules for names of connectors when creating parts? The wiki says it is important to note that within a part, a connector’s name and id attributes must be unique—that is, no two...
View ArticleHelp with importing PRT-12699
Does anyone have a file for a PRT-12699 sparkfun breadboard that can be imported into Fritzing ? Thanks, Mike 1 post - 1 participant Read full topic
View ArticleClik here to view.
Parts with top and bottom layer
Hi everyone. I managed to modify some parts of fritzing. Now I would like to move on to something more advanced on two levels (top and bottom pcb side). The part I want to do is this. Below I upload...
View ArticlePaying for PCB design
I am looking for someone to design a circuit based on LT3420 found here: https://www.analog.com/media/en/technical-documentation/data-sheets/3420fb.pdf I need the design ASAP so I can order the boards...
View ArticleSensores para baixar
Boa noite, procuro sensores de peso e de nivel de agua para baixar e não estou conseguindo encontrar, alguem poderia me enviar ? 1 post - 1 participant Read full topic
View ArticleCant export to Gerber
Hello, everyone. I’ve designed a pretty simple board, and it’s working fine on the breadboard, but when I try to export the file to a Gerber, Fritzing crashes and closes, and the folder contains only...
View ArticleError on compilig fritzing-app
Hi, I am trying to compile fritzing-app from source on Debian testing following the instructions of the wiki. However, I am receiving the following error: No rule to make target...
View ArticleAisler PCB - add parts
Hello everyone, Has anyone purchased any PCB from Aisler? When you add parts to the purchaising list they will be soldered on the pcb or only provided and the final costumer must solder it? Thank you...
View Article