Has someone ever developed a part for the SparqEE Cell 1?
@Miq1 wrote: I have a project that uses the SparqEE Cell 1 GSM module, but nowhere found a Fritzing part for it. Does anyone have a link to a resource providing it? Posts: 1 Participants: 1 Read full...
View ArticleBreadboarding Layer Issues
@MJ2909 wrote: I am having issues with breadboarding a circuit which requires a second breadboard. When I drag out the second breadboard from the parts list, the breadboard is placed in front of my...
View ArticleClik here to view.
3 Simple questions from a newbie
@maylo wrote: Hi! I am making a HAT pcb for RPi Ver.3. 1st question:How can I make the holes of the resistors smaller?They seem to be on the default 1mm, but I need them around 0.7-0.6. There is no...
View ArticleClik here to view.
Can not find Globalsat in fritzing
@Sergey232 wrote: sku_220363_1.jpg600x600 55.3 KB Posts: 1 Participants: 1 Read full topic
View ArticleGrove Dust Sensor PPD42
@igorfonseca83 wrote: Grove dust sensor: http://wiki.seeed.cc/Grove-Dust_Sensor/Grove Dust Sensor.fzpz (20.7 KB) Posts: 1 Participants: 1 Read full topic
View ArticleError in s1133 photodiode part
@12345678 wrote: Steps I took that resulted in the problem: Used the part as defined in my schematic and PCB layout. The schematic shows the diode symbol reversed with respect to the naming of the...
View ArticleTXS0108EPW Logic Level Converter
@moose4621 wrote: This 8-bit non-inverting translator uses two separateconfigurable power-supply rails. The A port tracks theVCCA pin supply voltage. The VCCA pin accepts anysupply voltage between 1.2...
View ArticleClik here to view.
DS1280 module - My first part, please comment
@bpuig wrote: Hello, This is my first part in Fritzing, so I'm asking for opinions to know if I did it right. Download is after all this text and images. This is the part I made, the DS1280 in a...
View ArticleHow to get out of "hand" mode
@cyborg5 wrote: Sometimes when editing and breadboard mode, my cursor changes from an arrow into a hand. After that all I can do is drag the entire design around. I cannot get cursor to go back to an...
View ArticleArduino Uploading on Fritzing
@furiousOne wrote: Hello Beginner here, Perhaps this has been answered before but I am trying to use the codeview for Arduino instead of the Arduino IDE however, when I use this and click upload it...
View ArticleSL6 x64 Intel Chip - installing & running Fritzing
@time wrote: I am new to Linux - SL6 was given to me as an OS.SL6 = Scientific Linux and simialr to RHEL6 or Fedora.I have downloaded the Linux 64 bit version and and unpacked it on my desktop. What...
View ArticleUnable to check for and update new parts
@tjlynchny wrote: Hi, I'm trying to install 0.9.3b on my Ubuntu 16.04 system. When Fritzing starts, I get an error message about "Cannot find parts", so, once Fritzing starts, I try Help->Check for...
View ArticleCategorize the Mine bin?
@grpace wrote: Is there a way to categorize/group the "my parts" bin ?Something similar to the way the Arduino bin and others are categorized ? Posts: 1 Participants: 1 Read full topic
View ArticleText labels in schematic view not included when exporting as SVG
@grpace wrote: Steps I took that resulted in the problem: Placed text labels in a schematic view.Exported the view as an SVG file.Labels not included in resulting SVG file.... What I expected should...
View ArticleClik here to view.
How to route out connections from the edge side of the RPi GPIO?
@8_bit_studio wrote: I am trying to make a raspberry pi add-on board, and I was wondering how I could get access to connections on the RPi's GPIO that are next to the edge of the board? I set the...
View ArticleRotary Switch - enclosed plastic
@Old_Grey wrote: PCB mounted enclosed plastic rotary switch - general eBay -. Dimensions based on - http://spec_sheets.e-switch.com/specs/G510440.pdfOthers based on -...
View ArticleClik here to view.
Any workaround for making a 4-layer PCB in Fritzing?
@AKdaBAOUS wrote: Hello Fritzing Community, I was wondering if anyone had any advice as to a potential workaround to create a 4-layer PCB in Fritzing? I've made several 2-layer PCBs and I would now...
View ArticleArbitrary Components for Breadboard View
@joshbg2k wrote: Hello, Hopefully the subject was worded well. I'm designing a PCB that has a bunch of 3.5mm headphone jack inputs. I know that the parts library has a number of them that I can drag...
View ArticleClik here to view.
Can FZ slot drill?
@Old_Grey wrote: Can FZ slot drill? I made the contacts rectangles and rounded the corners, but in the Gerbers there is no drill holes. Posts: 6 Participants: 2 Read full topic
View ArticleClik here to view.
Atmel AT89S51 DIP40 (8051)
@getabyte1432 wrote: Created using inkscape. AT89S51_40X1_schematic.png2000x1901 253 KB AT89S51.fzpz (10.7 KB)And individual .svg files can be extracted from it using 7-zip or other similar software....
View Article