Clik here to view.
Rendering linear gradient on breadboard part
Hello, Fritzing is having trouble rendering my custom breadboard component with linear gradient - the gradient appears blank. Please see the attached files. Is there any way to fix this?...
View ArticleClik here to view.
Please help me I want Male plug connector and Covinience outlet for my...
Male plug: 1 post - 1 participant Read full topic
View ArticleClik here to view.
Please help me I want Covinience outlet for my project diagram
Outlet: 1 post - 1 participant Read full topic
View ArticlePMSA003 sensor drawing for import to Fritzin
Hi! I am trying to find drawing for PMSA003 sensor. Any chance someone could share it with me? Or tell me how to get one??? 1 post - 1 participant Read full topic
View ArticleClik here to view.
Clik here to view.
How to Design a Custom GPIO Cable
Hi folks, now, as I am already doing final assembly of my project, I 'vefound out that I will have to make someone custom-make a GPIO cable for my Raspi 3B, as the quasi-standard GPIO cable with a...
View ArticleClik here to view.
Lora SX 1278 RF Module
i need this part for fritzing, anyone help me? 1 post - 1 participant Read full topic
View ArticleRF 433Mhz 5dBi SMA
searching for this part fzpz format 1 post - 1 participant Read full topic
View ArticleLooking for 5631AS and 5621AS 7-Segment Displays
Here’s the datasheet for the 5631AS Display. Here’s the datasheet for the 5621AS Display, for this one I need the 2nd model (the one on page 3). 1 post - 1 participant Read full topic
View ArticleCorrecting Parts
There is a guy named hubschrauber who built a VNH2SP30 motor driver and uploaded it into the fritzing forum. I tried to use that but seen somehow the PCB was not working. every pin is connected to a...
View ArticleClik here to view.
Fritzing gpl palette
Hello! I made a gpl palette (used in Inkscape) with colors from the graphic standards and some other colors used in Fritzing. Since the forum does not allow gpl files, i attached a pastebin link. I’d...
View ArticleClik here to view.
Inicio Fritzing
Hola ! Tengo inconvenientes con el inicio. Al arrancar queda trabado con el siguiente mensaje " Cargando esquematico nuevo" (con avance 14%) y no avanza mas. Como puedo solucionarlo? Muchas gracias 2...
View ArticleClik here to view.
BOSCH electrochemical Oxygen sensor
Hello, I am currently in search of a BOSCH LSH25 electrochemical sensor to create a circuit schematic, however, since it is specific I am not sure how I can either find it or create it. It would be...
View ArticleClik here to view.
Sharing insigts on using autoroutes
Hi PCB designers, I’m a Computer Science student from Denmark, researching for my master thesis. I want to investigate and potentially optimise tools used for routing PCB’s. And while I know stuff...
View ArticleClik here to view.
Esp32 pins question
which pins can i use as rx and tx on esp wroom 32? there are tx0 tx1 and tx2 my question is what are the differences between them and are there other pins i can use as tx and rx 1 post - 1 participant...
View ArticleClik here to view.
Making an arduino shield but i do not need all the pins on pcb
Hey guys. I am building a shield for my arduino mega. The question i have is that i will not be using all of the pins on the arduino. If you add an arduino in your project all of the pins will be a...
View ArticleClik here to view.
How can I change the word 'IC' on the top of chips
I have downloaded chips from here 74 series multiparts parts submit 74LS04.fzpz (7.3 KB) 74LS08.fzpz (7.9 KB) 74LS32.fzpz (8.7 KB) These are the same parts I uploaded earlier today in reply to a...
View ArticleGrove - 2.5A DC Current Sensor(ACS70331)
Hi, I am new to fritzing and not sure how to create a part whilst being on a tight deadline. Just want to ask if anyone has made the Grove - 2.5A DC Current Sensor (ACS70331). The data sheet is:...
View ArticleClik here to view.
1.54inch e-Paper Module Manual - Waveshare
Hello, Anyone can help me to get this part : 1.54inch e-Paper Module Manual - Waveshare Wiki 1 post - 1 participant Read full topic
View ArticleTwo-layer circuit board, hole management
I’m sorry but it’s the first time I try to make a 2 layer PCB. In my design I used one side for logic connections between components and the other side for voltage connections. What I don’t understand...
View Article